Al-10Mg型固溶合金自然时效稳定性研究

测定了ZL30 5合金自然时效 33年的力学性能变化 ,观察了晶界的析出相 ,研究了组织和性能的关系 ,从而确定了ZL30 5合金具有长期自然时效稳定性。     

Effect of Stoichiometry on Properties of Rare-Earth-Based Hydrogen Storage Alloy for Nickel-Metal Hydride Secondary Battery

Effect of stoichiometry on microstructures, electrochemical properties and PCT characteristics of the alloys MI(Ni0.71Co0.15-Al0.06Mn0.08)x (MI=Lanthanum-rich Michmetal, x=4.6~5.2) have been investigated. The lattice constants a, c, and cellvolumes of non-stoichiometric alloys are bigger than those of the stoichiometric alloy. With the increasing stoichiometry x,the value of a decreases, and the value of c and cell volume increases except for those of the stoichiometric alloy; the plateaupressure of PCT curve, discharge capacity and cycling stability all increase. The alloy with x=5.2 shows the highest dischargecapacity and the best cycling stability among the studied alloys.     

机械合金化Fe-Ni粉末的相结构

使用XRD和Moessbauer等方法，研究了在Ar气氛下机械合金化Fe—Ni粉末相结构的变化．结果表明，在机械合金化Fe64-Ni36粉末过程中，fcc相的数量随着球磨时间的增加先增加然后减少，与加乙醇球磨Fe64-Ni36的情形相同．当Ni的含量(原子分数)大于50％时，有fcc相、顺磁相和FeNi3形成，当Ni的含量低于50％时，bcc相的数量随着Ni含量减少而增加．Moessbauer谱的结果表明，因球磨时间或Fe、Ni比例的不同，Fe—Ni球磨粉末固溶体具有不同结构的原子配比。     

大块非晶合金的性能、制备及应用

综述了大块非晶合金的性能、制备方法及应用，对比了吸铸法制备的棒状Zr41.2Ti13.8Cu12.5Ni10Be22.5,Zr57Cu20Al10Ni8Ti5,Zr52.5Ti5Cu17.9Ni14.6Al10(原子分数)大块非晶样品的过冷温度区间宽度(△Tx)，给出了3种大块非晶合金系列的热稳定性参数Tg、Tx及△Tx，提出了大块非晶合金领域存在的问题及发展方向．     

铝薄膜CMP影响因素分析

提出了在碱性抛光液中铝薄膜化学机械抛光的机理模型,对抛光液的pH值、磨料、氧化剂浓度对过程参数的影响做了一些试验分析。试验结果表面粗糙度的铝薄膜所需的最优化CMP过程参数:硅溶胶粒径为15～20nm,pH值为10.8～11.2,氧化剂浓度为2.5%～3%。     

Finite element analysis of femoral components paper III – hip joints

Finite element analysis of the hip implant is conducted in this paper for representative femoral cross-section geometries and development of stress in the presence of bone cement is elucidated. Differences in cement stresses generated by varying implant cross-sections were compared with conventional features derived from representative implants. The analysis was performed under idealized implant assemblies by constraining the implant movement in the assembly. The cross-sections and implant geometries used are generic and intended to be representative of available geometries. This paper is a part of student research projects, prepared from a series of activities in biomedical implant research currently underway at Ohio Northern and Arkansas Tech Universities.     

Intergranular corrosion of a light aircraft aluminum alloy propeller

Examination of the wreckage of a light aircraft revealed that approximately 20 cm was missing from one tip of the aluminum alloy propeller. Fractographic and metallographic examination of the remaining portion of the propeller revealed extensive grain-boundary separation in the vicinity of the fracture, and grain edges and corners rounded by corrosion on the fracture surface. Energy dispersive X-ray analysis (EDXA) revealed fluorine on, and in the vicinity of, the fracture surface. In the ensuing litigation, it was asserted that the crash occurred because the propeller fractured in flight as the result of intergranular attack caused by the use of a fluorine-bearing cleaner.     

激光熔覆专用铁基合金粉末的研究进展

指出了目前防止熔覆层开裂所采取的主要措施中存在的问题,阐述了激光熔覆和热喷涂对于所用合金粉末性能要求之异同,评述了激光熔覆专用铁基合金粉末的研制现状,提出了成分与组织设计的新思想。     

镍铬合金在酸性CuCl2溶液中反应机理

对铜在酸性CuCl_2溶液中蚀刻反应机理论述,利用氧化-还原电动势原理,详细论述了Ni80Cr20合金在酸性CuCl_2溶液中化学蚀刻反应机理,以及影响蚀刻速度的因素,并对溶液中金属离子的存在形式作了验证。     

锰铜基高阻尼合金中锌量的测定──硫氰酸盐萃取分离络合滴定法

基于甲基异丁基甲酮于稀盐酸介质中定量地萃取Ｚｎ￣（２＋）与ＣＮＳ￣－形成的络阴离子。从而达到与共存的锰、镍、铝、铬的完全分离。在有氟化物、硫脲存在时Ｆｅ￣（３＋）、Ｃｎ￣（２＋）和Ａｇ￣＋也不被萃取。有机相中的锌于ＰＨ５．５“六胺”缓冲介质中返萃取回水相，用ＥＤＴＡ滴定。在文中给定的条件下锌的一次被萃取率可达９９％以上，成功地解决了锰铜基高阻尼合金中共存离子对锌量测定的干扰问题。